DIY Forum

DIY Forum/Home improvement advice

 

 

A-Z CONTENTS | ARCADE | DISCLAIMER | DIRECTORY | DIY VIDEO | HOME | SAFETY FIRST | FORUM RULES

It is currently Thu Feb 09, 2012 5:39 am
Visit Buck and Hickman


Time zone: Europe/London




 

Post new topic This topic is locked, you cannot edit posts or make further replies.  [ 8 posts ] 
Author Message
PostPosted: Sun Nov 01, 2009 6:36 pm 
Offline
Senior Member
User avatar

Joined: Sat Oct 31, 2009 7:33 pm
Posts: 220
Location: Zummerset
Has thanked: 0 times
Been thanked: 0 times
Have used this for some 7 years now and it needs replacing (batts pretty dead) was going to try out the dewalt version either 12, 14 or 18 volt. Before I do anyone have a recommendation of any make.

Thanks

Mike


Top
 Profile  
 
 Post subject:
PostPosted: Sun Nov 01, 2009 7:13 pm 
Offline
Pro Carpenter
User avatar

Joined: Sat Dec 16, 2006 10:11 pm
Posts: 9728
Location: redhill surrey an auld reekie laddie
Has thanked: 109 times
Been thanked: 406 times
i have the dewalt 18v angle drill nice bit off kit will drill with a flat bit ok 2 speed is handy

it would be improved if the battery could rotate on the base to allow it to get into tighter spaces

trigger is rather long and covers most off your fingers so its a bit awkward trying to hold at an angle without catching the trigger

apart from that gret bit off kit

_________________
we are all ------------------still learning


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

 Post subject:
PostPosted: Sun Nov 01, 2009 7:24 pm 
Offline
Senior Member
User avatar

Joined: Sat Oct 31, 2009 7:33 pm
Posts: 220
Location: Zummerset
Has thanked: 0 times
Been thanked: 0 times
Cheers buddy that was helpful. Mostly I use it for securing cornice to wall units and the 'H' fits between the top of the cornice and the ceiling most times. Anything much bigger will give me grief. Torque setting would be good when fitting door hinges but don't think any offer it.

Mike


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

 Post subject:
PostPosted: Sun Nov 01, 2009 7:35 pm 
Offline
Senior Member
User avatar

Joined: Fri Feb 01, 2008 11:02 am
Posts: 1303
Location: Dorset
Has thanked: 10 times
Been thanked: 108 times
If you're mainly using it as a screwdriver it maybe worth looking at the Bosch GWI 10.8V-Li Cordless Angle Screwdriver too. Also gives you the torque setting you require.

_________________
Cheers,
Darren

Property Refurbishment & Maintenance Dorset


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

 Post subject:
PostPosted: Sun Nov 01, 2009 7:42 pm 
Offline
Senior Member
User avatar

Joined: Sat Oct 31, 2009 7:33 pm
Posts: 220
Location: Zummerset
Has thanked: 0 times
Been thanked: 0 times
darrenba wrote:
If you're mainly using it as a screwdriver it maybe worth looking at the Bosch GWI 10.8V-Li Cordless Angle Screwdriver too. Also gives you the torque setting you require.


Thanks Darren, had not considered this one. I'll look at it first thing in the morning.

Mike


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

 Post subject:
PostPosted: Sun Nov 01, 2009 8:07 pm 
Offline
Pro Carpenter
User avatar

Joined: Sat Dec 16, 2006 10:11 pm
Posts: 9728
Location: redhill surrey an auld reekie laddie
Has thanked: 109 times
Been thanked: 406 times
darrenba wrote:
If you're mainly using it as a screwdriver it maybe worth looking at the Bosch GWI 10.8V-Li Cordless Angle Screwdriver too. Also gives you the torque setting you require.


although strangely enough its an electronic cluch it just stops dead but if you release and re-apply it will turn again
the several different position off the head is very usefull
the impact driver ir drill driver ar about the same sizeas an angle drill in there own right :wink:

_________________
we are all ------------------still learning


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

 Post subject:
PostPosted: Sun Nov 01, 2009 8:56 pm 
Offline
Senior Member
User avatar

Joined: Mon Jan 16, 2006 8:16 pm
Posts: 4537
Location: Somerset
Has thanked: 5 times
Been thanked: 86 times
Saw a tiny hitachi angle drill in one of the suppliers the otherweek, 1/4" hex chuck, little lithium battery thing, dont know what its like though...looks smaller than the one Darren linked to, but didnt have a flexi head....nor a second battery.



Here at SF

_________________
Why isn't the number 11 pronounced onety one?


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

 Post subject:
PostPosted: Sun Nov 01, 2009 10:31 pm 
Offline
Pro Carpenter
User avatar

Joined: Sat Dec 16, 2006 10:11 pm
Posts: 9728
Location: redhill surrey an auld reekie laddie
Has thanked: 109 times
Been thanked: 406 times
this is the full bosch kit the drills are simmilar looking to the hitch ones
http://cgi.ebay.co.uk/Bosch-10-8V-MONST ... 2555260d62

hitachi

http://shop.ebay.co.uk/i.html?_nkw=hita ... &_osacat=0

_________________
we are all ------------------still learning


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

Display posts from previous:  Sort by  
Post new topic This topic is locked, you cannot edit posts or make further replies.  [ 8 posts ] 


Similar topics
   

Time zone: Europe/London


Who is online

Users browsing this forum: No registered users and 0 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


News News Site map Site map SitemapIndex SitemapIndex RSS Feed RSS Feed Channel list Channel list
ultimatehandyman privacy policy

Contact

 

Powered by phpBB® Forum Software © phpBB Group

phpBB SEO

 

Diy forum - Decking - plastering - Plumbing - DIY - Tiling