DIY Forum

 

Ultimate Handyman Ultimate Handyman Ultimate Handyman Ultimate HandymanUltimate Handyman on Pinterest

 

DIY Forum/Home improvement advice forum

 

 

A-Z CONTENTS | DISCLAIMER | DIY VIDEO | HOME | SAFETY FIRST | FORUM RULES

It is currently Sun Dec 17, 2017 12:36 am
Visit Thermo worx


Time zone: Europe/London




 

 


Post new topic Reply to topic  [ 4 posts ] 
Author Message
PostPosted: Thu Nov 19, 2009 2:16 pm 
Offline
Mr. Grumpy

Joined: Tue Nov 18, 2008 3:41 pm
Posts: 2926
Has thanked: 19 times
Been thanked: 77 times
This review is aimed at the DIY novices who have never bought or used a jigsaw

A year ago I bought a cheapo Jigsaw from Argos, I didn’t know if I needed it so just got it anyway. Price £25. The picture shown is in blue but the one I got is grey, Apart from colour there is no fundamental difference.

For someone who is new to DIY you would be forgiven for buying such an item. It boast an 800W power, (jigsaws seem to typically start with 500W upwards), has strong pendulum action, on board laser, guide rail facility for extracting a dust extractor and left and right tilting base plate. All looks like value for money. The kit comes in a hard case and a selection of long blades (>100mm).

Intial appearance
On first appearance it looks like a strong capable machine but this is more due to ignorance of other known and quality brands. On closer look the body is 2 halves just snapped together and looked like it was about to come apart like a Kinder Egg exposing all the bits inside.

Use in practice
When you start using it some things become apparent very quickly. The base place has no indentations and just a set of markings so any angled cuts are guesswork. Moreso, the markings are totally incorrect and really serves no purpose. Also setting the nut to tighten the base plate is fiddly so as you tighten you rotate it further. Soft start is also missing

After a few cuts the problems really start to show. The laser is off line and has no means of adjustment. The most serious problem is the guide wheel. Far too much play, the cut line of the jig saw starts to deviate away. Cutting curves is no where near possible as the blade goes one way and the machine another. Any turning of the jigsaw causes the blade to pop out of the guide wheel. After very little use the guide wheel is so loose it simply rattles about.

Vibration is very noticeable too, at full pendulum action and speed it’s quite bad for a power tool.

Supplying very long jigsaw blades is pointless, it seems to suggest that you could cut out a hole for a kitchen sink or attack 3” thick timber with ease. No chance what so ever, 18mm ply is a struggle to get a smooth line. The machine has been given an apparently a large motor and poor housing to simply can’t take the pressure. Any sort of forward pressure will soon push back the guide wheel into the housing and has to be prised back out again

Also it’s a dangerous machine, the lock on switch is easily activated and quite fiddely to turn off so stopping the machine quickly is not a smooth operation

Overall
This is a pointless machine and should be avoided at all costs. You will waste more material and do more damage than good using it. I tried it cutting sections for pipe access and some cut out sections in vanity units. You end up making sh#t out of your furniture. The only possible use for this that I can see is to cut a section of loose timber if you have no saw or surface to lean on. Buying cheapo tools can often suffice for a few simple household tasks and will do the job before it breaks, .... but this can’t even attempt one task

I tried to think of one positive point about it and apart from a long lead, there is none!

Avoid, waste of money (1/10)


Attachments:
Challenge.jpg
Challenge.jpg [ 13.44 KiB | Viewed 8464 times ]
Share on FacebookShare on TwitterShare on DiggShare on DeliciousShare on Google+
Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Thu Nov 19, 2009 8:00 pm 
Offline
Site Admin
User avatar

Joined: Sat Jul 16, 2005 8:06 pm
Posts: 23852
Location: Darwen, Lancashire
Has thanked: 1259 times
Been thanked: 1191 times
Good review.

Thanks John :thumbright:

_________________
Check out our nominated charity


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Thu Nov 19, 2009 11:10 pm 
Online
Jack Of All Trades
User avatar

Joined: Sun Dec 18, 2005 9:23 pm
Posts: 7113
Location: Whitley Bay
Has thanked: 186 times
Been thanked: 253 times
At least it got a point for the lead!.... :wink:

_________________
By eck! ©


Top
 Profile  
Reply with quote  
 Post subject:
PostPosted: Tue Jan 05, 2010 8:03 pm 
Offline
Senior Member

Joined: Wed Apr 16, 2008 7:49 pm
Posts: 6230
Location: south tyneside
Has thanked: 42 times
Been thanked: 508 times
i used to work with a lad who was actually fairly clumsy. but he managed to break his wrist when a challenge cordless drill chuck jammed up as he was putting a bit into it. the whole machine snapped in half.

recomend avoiding the entire range.


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 


Similar topics
   

Time zone: Europe/London


Who is online

Users browsing this forum: No registered users and 0 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


 

 

 

News News Site map Site map SitemapIndex SitemapIndex RSS Feed RSS Feed Channel list Channel list
ultimatehandyman privacy policy

Contact

 

Powered by phpBB® Forum Software © phpBB Group

phpBB SEO