DIY Forum

DIY Forum/Home improvement advice

 

 

A-Z CONTENTS | ARCADE | DISCLAIMER | DIRECTORY | DIY VIDEO | HOME | SAFETY FIRST | FORUM RULES

It is currently Wed Feb 08, 2012 6:38 pm
Visit Buck and Hickman


Time zone: Europe/London




 

Post new topic Reply to topic  [ 39 posts ]  Go to page 1, 2, 3  Next
Author Message
PostPosted: Wed Mar 24, 2010 12:09 am 
Offline
Pro Handyman
User avatar

Joined: Sun Nov 19, 2006 4:31 pm
Posts: 3429
Location: North West, England, United Kingdom
Has thanked: 18 times
Been thanked: 26 times
When applying PTFE tape in conjunction with an olive compression coupling DON'T put the tape in the threads, only round the olive.


If you have to drain off and remove a radiator for decorating etc. and want to blank the 1/2" outlets.

And you don't have one of these ...

Attachment:
cap.jpg
cap.jpg [ 11.35 KiB | Viewed 1564 times ]

Take .......
A 5p piece,

Attachment:
FivePence.jpg
FivePence.jpg [ 9.64 KiB | Viewed 1564 times ]


a rubber 1/2" washer....

Attachment:
washer.jpg
washer.jpg [ 9.68 KiB | Viewed 1564 times ]


or a fibre washer ....
Attachment:
washer2.jpg
washer2.jpg [ 10.87 KiB | Viewed 1564 times ]


and a 1/2" nut (off a ballofix valve or a straight coupling or other fittings) can do the job! Just be sure you get the right thread!


If you are replacing a Fibre washer, while you get everything ready, pop the washer in your mouth to moisten it and it will swell and make a sweet connection when you tighten it up.

_________________
Jaeger.
Senior Member doesn't mean I'm OLD!

darrenc wrote:
I dont think its a stupid question but does show a lack of understanding of how paint works and reasons for certain applications, now dont jump down my throat Jaegar i'm not being funny its just a classic case in point of a well educated professionally trained painter against a general tradesman.

Image


Top
 Profile  
 
 Post subject:
PostPosted: Fri Mar 26, 2010 11:23 pm 
Offline
Pro Handyman
User avatar

Joined: Sun Nov 19, 2006 4:31 pm
Posts: 3429
Location: North West, England, United Kingdom
Has thanked: 18 times
Been thanked: 26 times
You only need one set (5p) per radiator this usually fits on the TRV side the other side has the lock shield and can be screwed down closed.

If you wish to add more tips to this thread you can do so.

If you wish to discuss the thread you can do so here-

http://www.ultimatehandyman.co.uk/forum ... 28945.html

_________________
Jaeger.
Senior Member doesn't mean I'm OLD!

darrenc wrote:
I dont think its a stupid question but does show a lack of understanding of how paint works and reasons for certain applications, now dont jump down my throat Jaegar i'm not being funny its just a classic case in point of a well educated professionally trained painter against a general tradesman.

Image


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Mon Jun 14, 2010 9:46 pm 
Offline
BANNED

Joined: Mon Jun 14, 2010 4:15 pm
Posts: 4
Has thanked: 0 times
Been thanked: 0 times
Hi

Just to let you al know, I managed to find a ompany who sells baywindow radiators..curved or angled....They were recommended by my neighbour.

The company is called Spam removed mod 1

My radiator was delivered in 2 weeks and fitted perfectly.

The price was reasonable and the customer service was great too.

Try them, as i have recommended them to my family and friends.

Whislt on there website I fell in love with tere VAAZ radiator which they colour matched to my worktop...and its defiently the wow factor in my kitchen.

Good luck
:cheers:


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Wed Jun 16, 2010 12:42 am 
Offline
Pro Handyman
User avatar

Joined: Sun Nov 19, 2006 4:31 pm
Posts: 3429
Location: North West, England, United Kingdom
Has thanked: 18 times
Been thanked: 26 times
WOW, that's a great tip!

Thanks MUM!

_________________
Jaeger.
Senior Member doesn't mean I'm OLD!

darrenc wrote:
I dont think its a stupid question but does show a lack of understanding of how paint works and reasons for certain applications, now dont jump down my throat Jaegar i'm not being funny its just a classic case in point of a well educated professionally trained painter against a general tradesman.

Image


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Tue Aug 10, 2010 4:19 pm 
Offline
Newly registered Member

Joined: Mon Aug 09, 2010 1:30 pm
Posts: 7
Has thanked: 2 times
Been thanked: 0 times
Just a quick tip that every plumber knows but as I’m new to this forum, if you have a pipe that will not stop dripping and you want to solder it, get a bit of bread and ram it up the pipe with a pencil, this will hold back the water long enough to solder a good joint and the bread will easily flush out!
Funny point, when I asked the customer if I could have a slice of bread they would always offer to make me a sandwich.


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Tue Aug 10, 2010 6:12 pm 
Offline
Senior Member
User avatar

Joined: Sat Jan 10, 2009 3:49 pm
Posts: 6652
Location: hants/dorset border
Has thanked: 150 times
Been thanked: 508 times
:dunno: Wholemeal or White...

Take it everybody has seen "Toms top tips"
http://www.youtube.com/watch?v=GJMBiRDIT20&NR=1



there's about 40 of them.....

_________________
.

If you feel you have benefited from the Free advice given on the Forum, Please consider making a donation to UHM's Nominated charity, read all about it and donate here :

http://www.donnasdreamhouse.co.uk/


__________________________________
__________________________________

Verwood Handyman
I Know it says I'm On-line, but I might have just left myself logged in, whilst I'm out....


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Tue Aug 10, 2010 6:20 pm 
Offline
Senior Member
User avatar

Joined: Wed Nov 14, 2007 10:21 pm
Posts: 4854
Location: Northampton
Has thanked: 65 times
Been thanked: 330 times
wine~o wrote:
there's about 40 of them.....


Most of trhem are very good Wino-O but theres the odd one to watch out for, especially the one on air testing - thats very dodgy ::b

But the multimeter one I posted a while ago - Priceless :lol: :lol:

_________________
As always help on here is free, however if you think you have saved a decent sum of money why not click the link to find out about the charity we're currently supporting? A couple of quid makes a real difference.

donnas-dream-house-charity-t52110.html


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Sun Sep 26, 2010 8:27 pm 
Offline
Senior Member

Joined: Fri Jan 20, 2006 5:51 pm
Posts: 2993
Location: Essex
Has thanked: 16 times
Been thanked: 217 times
Bleeding obvious really but I have only just thought of this recently. The hook and loop sanding pads for palm sanders and the like can be quite pricey. I buy the cheapest sheets i can get and just stick them on or trim them if I need to use the point.


DWD


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Sun Oct 31, 2010 8:02 pm 
Offline
Senior Member
User avatar

Joined: Sun Oct 31, 2010 7:56 pm
Posts: 271
Location: wigan lancs
Has thanked: 7 times
Been thanked: 49 times
and whats up with the testing tip, if done properly it could avoid you flooding your gaff. :dunno:
but anyrode thanks for the plug i hope you enjoy my tips there are over 60 now

tom


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Sun Oct 31, 2010 9:17 pm 
Offline
Senior Member
User avatar

Joined: Sat Jan 10, 2009 3:49 pm
Posts: 6652
Location: hants/dorset border
Has thanked: 150 times
Been thanked: 508 times
tomplum wrote:
and whats up with the testing tip, if done properly it could avoid you flooding your gaff. :dunno:
but anyrode thanks for the plug i hope you enjoy my tips there are over 60 now

tom

:welcomeuhm: Tom...loved all the tips i've seen so far....(Apart from the "Elvis impression...."

_________________
.

If you feel you have benefited from the Free advice given on the Forum, Please consider making a donation to UHM's Nominated charity, read all about it and donate here :

http://www.donnasdreamhouse.co.uk/


__________________________________
__________________________________

Verwood Handyman
I Know it says I'm On-line, but I might have just left myself logged in, whilst I'm out....


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Sun Oct 31, 2010 9:32 pm 
Offline
Senior Member
User avatar

Joined: Sun Oct 31, 2010 7:56 pm
Posts: 271
Location: wigan lancs
Has thanked: 7 times
Been thanked: 49 times
ha ha wino, i've took elvis off for now, but he's coming back with a new video soon. :huray:


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Sun Oct 31, 2010 9:35 pm 
Offline
Senior Member
User avatar

Joined: Sat Jan 10, 2009 3:49 pm
Posts: 6652
Location: hants/dorset border
Has thanked: 150 times
Been thanked: 508 times
tomplum wrote:
ha ha wino, i've took elvis off for now, but he's coming back with a new video soon. :huray:




I'll look forward to it.... :shock:

_________________
.

If you feel you have benefited from the Free advice given on the Forum, Please consider making a donation to UHM's Nominated charity, read all about it and donate here :

http://www.donnasdreamhouse.co.uk/


__________________________________
__________________________________

Verwood Handyman
I Know it says I'm On-line, but I might have just left myself logged in, whilst I'm out....


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Thu Dec 02, 2010 9:27 pm 
Offline
Senior Member

Joined: Tue Nov 30, 2010 10:27 pm
Posts: 286
Has thanked: 10 times
Been thanked: 21 times
Best tip and EVERYBODY needs to be told lol:

When soldering up to or near valves or iso's of any sort, especially brass end feed drain offs..... strip em down first! dunno how many jobs I go to where the valve rubber has been "stuck" to its seat through torching next to it, blumin nuisance and so easy to get right in the first place.
Dont think inline iso' valves can be stripped so a quick wet strip off coth wrapped around it works too.

Another cracker is when soldering a pipe over a painted surface eg. skirting’s & you know your heat mat is deffo gonna set of the smoke alarm, mix a bit of thick wall paper paste & paint it onto the surface you don’t want to burn, works a treat soldering upwards inside a floor space too. I got the idea from flat roofing, anywhere you dont want excess tar, paint it with paste first, dead neat!


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Thu Dec 02, 2010 9:42 pm 
Offline
Senior Member
User avatar

Joined: Sat Jan 10, 2009 3:49 pm
Posts: 6652
Location: hants/dorset border
Has thanked: 150 times
Been thanked: 508 times
Best tip....get your boiler serviced before winter.....snug-as-a-bug-in-a-rug..... :wink:

_________________
.

If you feel you have benefited from the Free advice given on the Forum, Please consider making a donation to UHM's Nominated charity, read all about it and donate here :

http://www.donnasdreamhouse.co.uk/


__________________________________
__________________________________

Verwood Handyman
I Know it says I'm On-line, but I might have just left myself logged in, whilst I'm out....


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Thu Dec 09, 2010 5:08 pm 
Offline
Senior Member

Joined: Tue Nov 30, 2010 10:27 pm
Posts: 286
Has thanked: 10 times
Been thanked: 21 times
used Toms Tip today lol, heres another one... if you're going to go to all the hassle of mains flushing a system, replace all the valves too! re-connected everything, bled rads etc, weeping lock shield olive with no drain cock.... gutted lol.


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 39 posts ]  Go to page 1, 2, 3  Next


Similar topics
   

Time zone: Europe/London


Who is online

Users browsing this forum: darrenba, Petemate, ropper and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


News News Site map Site map SitemapIndex SitemapIndex RSS Feed RSS Feed Channel list Channel list
ultimatehandyman privacy policy

Contact

 

Powered by phpBB® Forum Software © phpBB Group

phpBB SEO

 

Diy forum - Decking - plastering - Plumbing - DIY - Tiling