I have come across all these nasties whilst out and about in, and all in the last year or so

Enjoy!!

This picture needs very little explanation.



==============================================

I got called to a house by a customer who said her shower stopped working about a week ago, and yesterday she heard a bang and some fizzing in the bathroom.

This is what I found under a floorboard:



It is a white sheathed 6.0mm² T&E cable, which was sat in a notch in the top of a joist with a nail through it. The joist and floorboard were charred, and the live, earth and all but three strands of the neutral have vaporised.

It was fed from a non RCD circuit with a 45A rewireable fuse which had not blown, so the cable was still live when I arrived.

The customer had been stood on the the floor with wet, bare feet after a bath.

=============================================

Breif history:

Extention / loft conversion to a bungalow. Original sparkie went AWOL. He had replaced the consumer unit, but left this under the floorboards below the consumer unit / intake.





The 1.5mm² SWA feeds a fairly well loaded 6 way CU in the garage. The joint box is fed in 2.5mm² fed from the 32A socket MCB. The armouring is no longer earthed either.

=============================================

This was taken in an under the stairs cupboard which has been converted to a downstairs WC.

The room did not border an external wall, so the soloution for the fan?



=============================================

This picture is of a CU with a loose screw connecting the neutral bars together.


The load was relativly light as the CU fed a portakabin.
There were 2no. 2kW panel heaters, 3no. 4' fluorescents and 4no. twin sockets.


You can see where the burning has been painted over on the trunking and ceiling












=============================================

This picture is of a fluorescent fitting in a factory.

It is fed from 2no. 1mm² red singles in PVC tube. Not a CPC in sight.



==============================================

Here is a 60VA DL transformer which stopped working, and was found sat on a DL lamp.




==============================================

Nice meter tails. 4.0mm² rubber twin cable. It had gone all crumbly.
Cutout fuse was a 100A BS 88



==============================================

This picture is of a pull switch.

A studwork wall was put up right where the 2 way pull switch was located.

What to do? Move the pull switch 2 inches? Oh no, that would be far too simple! Lets just cut the string off, and plaster it in to the new wall!

It had been like this for a good long while, and was still live when we arrived to rewire the lights!



============================================

This picture is of a fuse box. It was still live until last week, when the head / meter fell off the wall. The dno arrived and replaced this but refused to reconnect.

Wonder why

Kitchen fuse box

Note the fused neutrals, asbestos and wooden enclosure



The kitchen fuse box was fed from this mess



I refused to reconect it too

=============================================

This picture is a flush mounted 4 way wylex CU, which is supplied from an external meter box. The tails run through the cavity and enter through an oversized hole in the rear of the CU.

Not a problem until cavity wall insulation was installed!



=============================================

This is a GU10 downlighter.
It is connected to phase and earth only, yet it is on and working.
The neutral can be seen not connected just to the left of the DL.



=============================================

== Metal Clad FCU ==
This MEM FCU has had it's fuse holder retaining screw snapped off, and as these FCUs have a spring loaded fuse carrier it has been wedged in place with a matchstick.



=============================================

== Big Commercial Mess ==
In a cupboard in a nightclub in Leeds. Also feeds 4 offices and a shop above.







=============================================

== DNO cable repair ==
DNO cable accidentally got severed during some building work. Tho DNO attended and repaired it.
It does not feed anything in this building. It feeds the shop above.







=============================================

== Fusebox Fire ==
This is a proteus fusebox (Its a wylex copy)
The circuit fed a 9.5kW shower on a 6.0mm² t&e cable. The fuse was a 45A rewireable. These boards are designed for a maximum of 30A per outgoing way.





=============================================

== Hidden Joint Boxes ==
A couple of nasty joint boxes found hidden under floors.





=============================================

== Bath Socket ==
A socket rather close to a bath
(The bath was just being stored there on a new build project, but made for a good photo)

Nice collection of bad electrics!

Good to see they've made it to the rougues gallery!

_________________
Hinton Heating

i think the last one is the worst

just imagine that, storing a bath next to a plug... I hope the plumber is Part P registered to place a water carrying device, so close to a socket... Was is notified?

_________________
Hinton Heating

There's no grommet on the back box on the first picture, I'm appalled that you didn't point this out

That is an awesome collection

Some of those pictures are very scary

_________________
DIY | Donnas dream house

I like the extractor fan in the floor

_________________
Why isn't the number 11 pronounced onety one?

sure are some scary things happened there i have come across some frighting sights in the electrics but thankfully nothing as bad as any of these

_________________
diy is for real not for fun

The fan next to the toilet was good....one slip and its 'sh*t hits the fan'

It's scary how close people can live to death without knowing it. It's not a pleasant thought and supports the argument for regulated working practices, however much they "get in the way".

I'm appalled at this post and can't believe people can do jobs like this and are able to sleep at night. They've got to be absolultely useless, because it doesn't take any longer to do a right correctly.

Holy Cow. I'm fairly new to electrical work and have only just passed my
Part P. I can see now why they introduced it !!

They introduced part p as a stealth tax

_________________
DIY | Donnas dream house

Part P wont stop bad workmanship like this... most bad DIYers will continue as they always have, and stick 2 fingers up to Part P, just as they do to Corgi!

Can we get this on the 2nd page, as takes ages to scroll thro all those pictures!

_________________
Hinton Heating

please! 8-)

_________________
Hinton Heating