DIY Forum

DIY Forum/Home improvement advice

 

 

A-Z CONTENTS | ARCADE | DISCLAIMER | DIRECTORY | DIY VIDEO | HOME | SAFETY FIRST | FORUM RULES

It is currently Fri May 25, 2012 3:27 am
Visit Buck and Hickman


Time zone: Europe/London [ DST ]




 

Post new topic This topic is locked, you cannot edit posts or make further replies.  [ 10 posts ] 
Author Message
PostPosted: Tue Nov 29, 2011 9:13 am 
Offline
Newly registered Member

Joined: Mon May 09, 2011 4:59 pm
Posts: 59
Has thanked: 11 times
Been thanked: 1 times
Hi all

I have an old lead pipe water feed, which runs from my water meter on the pavement across my garden, then under my living room floor before it appears in the kitchen. It then come out of the floor, feeds upstairs to the bathroom and spurs off back under the floor to feed the ground floor.

I have just had the kitchen refited and reworked the pipework under the floor, what I plan to do if feasible is to lay a new water pipe into my downstairs toilet (straight from outside), fit a new stop tap and fit it into the existing cold water feed in here, it is about 3 meters from the exisiting entry point and then remove the old tap and internal lead piping. What I would like to know is if this is allowable under regulations, and whether anyone thinks the extra distance the water will need to travel will be an issue.

If there are no issues my plan would be to fit the stop tap and blue pipe and run the feed into the cold water pipes (with the stop tap closed) in the downstairs loo, ready for switchover to the new supply, then it would just be a case of turning on the new stop tap when the water board turn up and allowing me to remove the old internal lead piping at my leisure.

Thanks

Craig


Top
 Profile  
 
PostPosted: Tue Nov 29, 2011 10:06 am 
Offline
OAP
User avatar

Joined: Mon Mar 10, 2008 12:46 am
Posts: 39985
Has thanked: 187 times
Been thanked: 2114 times
All the work is notifiable before you start.

Replace the lot back to the meter would be the best bet, the supplier may do it under a lead replacement program if you ask.

_________________
If you feel you have benefited from the Free advice given on the Forum, Please consider making a donation to UHM's Nominated charity, read all about it and donate here :

donnas-dream-house-charity-t52110.html


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Tue Nov 29, 2011 10:11 am 
Offline
Newly registered Member

Joined: Mon May 09, 2011 4:59 pm
Posts: 59
Has thanked: 11 times
Been thanked: 1 times
Hiya

I plan to replace the full lead pipe under the replacement scheme with the new blue poly pipe, I plan to connect at the new point in the house, who is it notifiable too?

Cheers

Craig


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Tue Nov 29, 2011 10:24 am 
Offline
OAP
User avatar

Joined: Mon Mar 10, 2008 12:46 am
Posts: 39985
Has thanked: 187 times
Been thanked: 2114 times
Water supplier.

_________________
If you feel you have benefited from the Free advice given on the Forum, Please consider making a donation to UHM's Nominated charity, read all about it and donate here :

donnas-dream-house-charity-t52110.html


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Tue Nov 29, 2011 10:33 am 
Offline
Troll Headbutter
User avatar

Joined: Sat Jan 01, 2011 8:20 pm
Posts: 1886
Has thanked: 77 times
Been thanked: 130 times
Scruff, how does the lead replacement programs work?

Do they do the whole thing (I guess it's done using a mole?) and any idea of typical cost - or is it per house basis?

My rising main is lead...(not done me any harm DUrrrrrrrrrrrrrrrrrrrrrrrRRRRRRRRRR :mrgreen: )

BG


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Tue Nov 29, 2011 10:38 am 
Offline
OAP
User avatar

Joined: Mon Mar 10, 2008 12:46 am
Posts: 39985
Has thanked: 187 times
Been thanked: 2114 times
If the supplier has a replacement program it could be free.

Normally you dig and lay the pipe and they'll do the connection FOC.

For the OP, it needs 750mm cover, and an entry sleeve into the building, 750mm from the outside wall.

_________________
If you feel you have benefited from the Free advice given on the Forum, Please consider making a donation to UHM's Nominated charity, read all about it and donate here :

donnas-dream-house-charity-t52110.html


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Tue Nov 29, 2011 10:43 am 
Offline
Newly registered Member

Joined: Mon May 09, 2011 4:59 pm
Posts: 59
Has thanked: 11 times
Been thanked: 1 times
HIya

Thanks for the info, I have read the regs, not really sure what the entry sleeve is, or how its meant to work. The picture on it are a bit confusing.

My understanding is that I have to run the blue pipe 1m underground then it needs to enter the building and be insulated and put in ducting (no idea what this is or where to buy it) I am not sure if I can run the pipe in through the external wall and then bring it immediately up that wall. To connect into my pipework.


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Tue Nov 29, 2011 10:49 am 
Offline
OAP
User avatar

Joined: Mon Mar 10, 2008 12:46 am
Posts: 39985
Has thanked: 187 times
Been thanked: 2114 times
Where the pipe enters the building it goes in a duct, normally a 100mm flexible pipe and sealed both ends.

You maintain the minimum 750mm from the outside into the building or it can be insulated where that is not practical.

_________________
If you feel you have benefited from the Free advice given on the Forum, Please consider making a donation to UHM's Nominated charity, read all about it and donate here :

donnas-dream-house-charity-t52110.html


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Tue Nov 29, 2011 10:53 am 
Offline
Newly registered Member

Joined: Mon May 09, 2011 4:59 pm
Posts: 59
Has thanked: 11 times
Been thanked: 1 times
Thanks scruff

That seems a lot clearer for the external pipe work, can you see any issue with my plan?

Cheers

Craig


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

PostPosted: Tue Nov 29, 2011 11:04 am 
Offline
OAP
User avatar

Joined: Mon Mar 10, 2008 12:46 am
Posts: 39985
Has thanked: 187 times
Been thanked: 2114 times
No real issues depending on your supplier.

They may want to inspect the internal work before they do the connection.

You need to talk to them and get the inspector involved

_________________
If you feel you have benefited from the Free advice given on the Forum, Please consider making a donation to UHM's Nominated charity, read all about it and donate here :

donnas-dream-house-charity-t52110.html


Top
 Profile  
 
You may not be able to see the full post including pictures unless you register or log in

Display posts from previous:  Sort by  
Post new topic This topic is locked, you cannot edit posts or make further replies.  [ 10 posts ] 


Similar topics
   

Time zone: Europe/London [ DST ]


Who is online

Users browsing this forum: No registered users and 0 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


News News Site map Site map SitemapIndex SitemapIndex RSS Feed RSS Feed Channel list Channel list
ultimatehandyman privacy policy

Contact

 

Powered by phpBB® Forum Software © phpBB Group

phpBB SEO

 

Diy forum - Decking - plastering - Plumbing - DIY - Tiling